Axus PA-08 Manuel de service Page 185
- Page / 252
- Table des matières
- MARQUE LIVRES
- 415B/425 1
- * SERVICE MANUAL * 2
- TNC 415B / 425 2
- Table of Contents 4
- 2. Minor Error Messages 7
- SERVICE MANUAL TNC 415B/425 10
- Error Location 15
- 5. LOGIC UNIT LE 415B/425 20
- 6.2.1 Connectors on PL 400 31
- 6.2.2 Pin Layout: PL 400 32
- 6.2.3 Connectors on PL 405 34
- 6.2.4 Pin Layout: PL 405 35
- 6.2.5 Connectors on PL 410 36
- 6.2.6 Pin Layout: PL 410 37
- 6.2.7 Connectors on PA 110 40
- 6.2.8 Pin Layout: PA 110 41
- 6.3.1 Connectors on TE 400 42
- 6.3.2 Pin Layout: TE 400 43
- 6.3.3 Connectors on TE 410 44
- 6.3.4 Pin Layout: TE 410 45
- TNC 415 Block Diagram 48
- 8. Board Description 50
- 10. Power Supply 54
- 10.2 Power Supply of the NC 56
- Voltage Table 57
- 10.4 Power Supply of the PLC 63
- 10.5 Buffer Battery 66
- 11. Keyboard Unit TE 400/410 67
- TE 410 Id.No. 264 105 68
- 12.1 Overview 78
- BC 110, Id.No. 254 740 01 79
- 13.1.1 Error Causes 81
- 13.1.2 Error Location 81
- Flow-Chart for Error Location 82
- 13.2.1 Error Causes 83
- 13.2.2 Error Location 83
- 14. Electronic Handwheels 86
- 14.2 Handwheel HR 332 87
- 14.3 Error Messages 88
- 15. 3D-Touch Probes 89
- 15.2 Error Messages 90
- 16. Data Interfaces 92
- Operating Modes 93
- 16.3 Error Messages 95
- (simplified wiring) 100
- 16.4.3 RS-422 Data Interface 101
- 17. Data Input and Output 102
- 17.3 External Data Output 104
- .H, .I, .T, .D, .P, .A, .PNT 105
- 9 5 1 4 8 107
- 1 0 5 2 9 6 108
- 8 0 7 6 6 7 109
- Selecting the Drives 111
- the POCKET TABLE 116
- Betriebsart FE1 117
- 18. Analogue Outputs 125
- 7 5 3 6 8 131
- 18.6 Oscilloscope Function 134
- 18.6.1 Soft Key Rows 135
- 18.6.2 Trigger 136
- 18.6.3 Recording 136
- 19. PLC Inputs and Output 138
- 19.4.1 TRACE Function 142
- 19.4.2 LOGIC Diagram 143
- 19.4.3 TABLE Function 145
- Operation " 148
- 20. Test Units 150
- Page 146 151
- Issue: 20.08.95 151
- 152
- 21. Exchange Instructions 153
- 21.1.4 Backing up RAM Data 154
- WARNING: 158
- 21.4 Exchanging the CLP Board 163
- 21.4.3 Mounting the CLP Board 165
- 21.8 Exchanging the EPROMs 174
- MACHINE PARAMETER LIS 175
- 1.0 TNC 176
- 415B/425 176
- 1.0 TNC 177
- 1.0 TNC 178
- 415 B/425 178
- 1.0 TNC 182
- 1.0 TNC 184
- Operation with Servo Lag 193
- R H Tables for 199
- 415B/425/426 199
- Integral PLC 211
- 1.0 TNC 223
- 415 B/425/426 223
- Tool Calibration with TT 110 226
- Display and Programming 229
- User Parameters 237
- Machining and Program Run 241
- 1.0 TNC 241
- Tilting the Working Plane 245
- Hardware 248
© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels